How to make a layout for a prototype?

When developing microcontroller firmware, you have to debug it on prototypes. The prototype is just a set of debug boards connected by jumpers.

Prototypes are especially relevant when the board of the combat device is still in development (production), and the software already needs to be developed and debugged somehow, then you have to assemble a prototype from a set of debug boards.

The fact is that we are not working here in zero gravity, and if we simply connect the boards with jumper wires, they will suddenly fall off under the action of a tension force.

Therefore, it is necessary to fix the boards hard on one common base and then only connect them with jumpers.

It is also often necessary to install on an expensive premium PCB board protective screenso that when transporting without a box in a backpack, the components on the board are not scratched, for example, with keys. Or it is trivial to protect the board from coffee accidentally spilled on the table.

fig.1 PCB with protective screen
fig.1 PCB with protective screen

I was surprised to learn that people have problems with the manufacture of such substrates (screens) for PCB prototypes.

What is the difficulty?

The point is that we need a lot high accuracy drilling holes (hundredths of a millimeter), and the position of the holes relative to each other can be simply random (s) like the position of a cluster of stars in the sky.

Therefore, it follows instruction how to make a quality base for a prototype.

What do you need from the equipment (hardware)?

Equipment

Purpose

category

plexiglass

To make a backing or shield

consumable

plastic racks

to bond the board and substrate

consumable

plastic nuts

to bond the board and substrate

consumable

plastic bolts

to bond the board and substrate

consumable

a printer

To print a drawing

tool

USB Flash(ka)

To download a drawing to the printer

tool

Kerner

For tapping funnels at the places of future drilling

tool

A4 paper

To print a drawing with marking of drilling places

consumable

Calipers

To take dimensions from the board

tool

Ruler

To check the drawing after printing

tool

Scotch

to stick the drawing on plexiglass

consumable

hand drill

for drilling holes

tool

Drill 2mm

pre-hole drilling

tool

Svelo 3mm

drill hole

tool

Drill 5mm

for chamfering

tool

Flat screwdriver 4mm

To screw the board stands and backing

tool

Why plexiglass? It transparent. You can always read the silkscreen of the board from the back through the glass and you do not need an endoscope for this.

What do you need from the software?

Program

Purpose

inkscape

To draw a drawing

pdf viewer

To view and check a drawing before printing

1–Draw a drawing in inkscape. Inkscape is a free and simple 2D drawing utility.

2–Print out the drawing in scale one to one (M 1:1). You may have to split A3 into two A4s. Be sure to check with a ruler after printing that the drawing is actually M 1: 1

3– Stick the drawing on the plexiglass. In this particular case, you need to add new holes to an existing substrate, so I had to stick the drawing on the back of the org glass.

4–And now a very responsible step. Gotta get a manual automatic center punch (automatic punch tool) and carefully prick the funnels in the places of future drilling.

5–Drill holes first with a thin drill (2mm). It is important. If you make a mistake, you can re-drill next to the same thin drill. Then we drill with the necessary 3mm drill. And make a chamfer with a 5mm drill. A chamfer is required so that the bolt enters at different angles.

6–Screw the boards onto the plastic standoffs with a flathead screwdriver.

This is how the Bluetooth speaker prototype turned out.

If you do not have all this equipment in your bedroom, then this is not a problem.

You can print the drawing, for example, in the same city printing house, they guarantee printing on a scale of M 1: 1.

The blank itself can be taken to the nearest shopping and entertainment center (SEC). As a rule, in the basements of the mall (shkek) there is a jewelry or shoe workshop and you can drill or saw off in plexiglass there. It will cost about 500 RUR and 2-3 weeks of waiting. However, you will have to print the drawing and paste it yourself beforehand.

Conclusion

Make beautiful prototypes on a Plexiglas substrate, it’s not hard at all.

Aircraft modellers even have a saying:

If the product is ugly, then it will not fly.

Therefore, the prototype should also look beautiful.